Pedals

Lightweight one-piece Polypropylene thermoplastic pedals with in-molded grip nodes. - Proportionally smaller platform size is perfect for smaller-sized feet - Durable 7mm boron steel axle - Loose ball bearing axle assembly - Built-in reflectors included - 9/16" / 1/2" axle options - 300g per pair - Dimensions: 93 x 87mm

Shorter 7mm rear load pins for the outer extremities of SPOON, SPIKE, and OOZY pedals. - Provide durability and improved safety - Mix and match with the longer stock pins to customize your ideal amount of grip

Pre-cut traction tabs designed to integrate with the Highline remote lever and increase grip for ultimate control.

IGUS Bushing replacements for your Spike or Oozy pedals help to eliminate any play that develops over time, and revive smooth spinning action. - 2pcs IGUS self lubricating bushing - 2pcs O-ring - 2pcs stainless shim washer

Longer rear load pins for the outer extremities of your pedals provide ultimate durability, while shorter front load center pins create a virtual concavity in the pin pattern, increasing grip without sacrificing pedal body thinness. - 28pcs rear load pins - 16pcs front load pins - Tool included

Lightweight one-piece Polypropylene thermoplastic pedals with in-molded grip nodes. - Durable boron steel axle - Loose ball bearing axle assembly - Built-in reflectors included - 309g per pair - 9/16" / 1/2 axle options - Dimensions: 100 x 86mm

Protect the soles of your shoes with the Shoe Shields from Crank Brothers. These stainless-steel plates install under your cleats and prevent the pedal from digging in to your carbon-soled shoes. - Sold in pairs

Replacement bearings and bushings specific to Spoon 90 (Small) and 100/110 (Medium and Large) pedals. Eliminates play that can develop over time, and revives performance. Includes: - Sealed Bearing x2pcs - 10mm IGUS Bushing x2pcs - Green Friction Seal x2pcs - Locknut - O-ring x 2pcs

Lightweight and strong 1-piece Polypropylene thermoplastic body with a durable ED black (Electrodeposition) aluminum cage - Tough boron steel axle - Built-in cage flip tab and mounting points for toe clips - Loose ball bearing axle assembly - Tough and durable ISO Mountain approved - 300g per pair - 9/16" axle - Dimensions: 102 x 62mm

Crank Brothers' 5050 Pin Kit includes 40 8mm-long steel pins that let you customize the traction on your 5050 or Mallet pedals. Thread lock is pre-applied to every pin.

A nylon evolution of DMR's V12 body design. Equipped with the same concave footprint and narrow profile DMR pedals are known for, while spinning on a Dual DU bushing system to provide the value of a plastic pedal with a thoughtful approach to increased durability. - Chromoly axle - Dual DU bushing system - Full-length 6mm off-road pins for added grip

- Compatible with all Spike & Oozy Pedals - Full Complement Sealed Bearing x 2pcs - Green Silicone Friction Seals - Replacement inboard bearings for your SPIKE or OOZY pedals.

Lightweight and strong one-piece aluminum flat pedal in a premium barrel polished aluminum finish. - Tough 7mm boron steel axle - Loose ball bearing axle assembly - Reflectors included (removable) - 9/16" axle - Dimensions: 101 x 79mm - Silver - 368g per pair

Everything you need to fully rebuild your OneUp Composite Pedals. KIT CONTAINS: - 2 CARTRIDGE OUTER BEARINGS - 2 INNER DU BEARINGS - 2 OUTER SEALS - 2 AXLE NUTS - 2 INNER CAPS - 2 END CAPS

- Set of 44 total replacement steel pins for vault pedals - Run threads-out for maximum traction or flip the pins to heads-out for less grip - 16 Short pins (for use in the center) overall length 8.5mm, stud is 4.5mm - 28 Long pins (for use in the outside edge) overall length 12.5mm, stud is 4.5mm - Use either a 5mm spanner or the included 2mm hex wrench to secure/remove

X-TRACK cleats are compatible with all SPD-standard pedals, utilizing 2-screw mounting for an ultra compact profile and lightweight. X-TRACK Easy cleats provide a 13° angle of disengagement and allow for multidirectional release. - Compatibility: X-Track and Geo Trekking Collection, SPD compatible - Material: Premium Steel - Clip out direction: Multidirectional - Clip in: 30% easier - Angle of Disengagement: 13° - Lateral Adjustment: 2mm - Angular Adjustment: 1° - Weight (pair): 45g

Everything you need to fully rebuild your OneUp Aluminum Pedals. Our V2 kit is compatible with all OneUp Aluminum pedals. The brass bushings take the place of the 3 small cartridge bearings and aluminum washer that were on our original pedal assembly. KIT CONTAINS - 2 LARGE OUTER BEARINGS - 2 BRASS BUSHINGS - 2 OUTER SEALS - 2 FLANGE WASHERS - LH AND RH AXLE BOLTS - 2 AXLE O-RINGS - LH AND RH BEARING NUTS

Wheels Manufacturing Pedal Washers help distribute the forces of a pedal spindle on your expensive crank arms and allow you to torque pedals properly over and over again without damaging crank arms.

- The ATAC 13/17° cleat works with all TIME mountain pedals. - Included with all mountain pedal models numbered "6" and higher - Release angles of 13 degrees or 17 degrees depending on how the cleat is set up on the shoe - Compatible with all two-hole cycling shoes.

- The ATAC EASY 10° cleat works with all TIME mountain pedals. - Included with mountain pedal models numbered "2" and "4." - Release angle of 10 degrees and is compatible with all two-hole cycling shoes. - Don't let the "Easy" name fool you. If you are a high-performance rider looking to reduce the release angle from our 17 or 13 degrees, this is the choice for you.

- Works with all XPRO and XPRESSO pedals. - Not included with new XPRO and XPRESSO pedals. - This is a zero-float cleat design, so there are zero (0) degrees of heel float and no lateral float along the pedal axle. - Compatible with all three-hole road shoes, but the included shim may be required for shoes that have a large curvature in the forefoot area. Full details are included in the easy-to-use instructions.

- Developed for the TIME XPRO & XPRESSO road bike pedal range. - They allow angular and lateral freedom in order to respect the natural movements of your legs and joints. - You can also adjust the Q-factor (by switching the cleats) - The Bi-material brings more durability when walking with the cleats. - These cleats are the stock cleats included with all XPRO & XPRESSO pedals.

- Works with all RXS and Impact pedals. - Five degrees of heel float and 2.5mm of lateral float along the pedal axle. - Compatible with all three-hole road shoes, but the included shim may be required for shoes that have a large curvature in the forefoot area. Full details are included in the easy-to-use instructions.

- Pedal Grip pins/bolts and 4 tension screws TIME SPECIALE 8/12

Lightweight, low-profile full aluminum flat pedal - Barrel polished aluminum body with an ED black (Electrodeposition) or anodized silver aluminum cage - Built-in cage flip tab and mounting points for toe clips - Tough and durable ISO Mountain approved - Loose ball bearing axle assembly - Reflectors included (removable) - 9/16" CNC machined Cro-Mo axle - Dimensions: 97 x 63mm

A revolution in performance and reliability. The kit includes premium internal components: - Inner bearing o-ring x 2 - Spindle seal x 2 - Outer Igus solid bearing x 2 - Inner Igus solid bearing half x 4 - Bearing Retainer Bolt x 4 - Outer o-ring x 2 - Grease port screw x 2 - Compatibility: Stamp (2016), Stamp 7 (2017+), Stamp 11 (2017+)

Crank Brothers' Premium MTB Cleats are perfect for your Crank Brothers Eggbeater, Candy, Acid, Smarty, Mallet, and Quattro pedals. They're made from solid brass for crisp entry and exit, and top-notch durability. - SPD compatibility - Weight (pair): 30g - Float: 6 degrees - Release angle: 15 or 20 degrees

Cleats with a more forgiving 10-deg release. - Optimized for novice riders or those new to clip-in pedals - 10-deg release angle makes it easier to unclip - 2-hole bolt pattern for mountain bike shoes - Plastic spacing shims included - Compatible with all Crankbrothers clip-in pedals

Crank Brothers' Zero Float Cleats offer no pedal float for greater pedaling efficiency. They're made from solid brass for crisp entry and exit, and top-notch durability. - Weight (pair): 30 grams - Shoe compatibility: SPD - Release angle: 15 degrees

Versatile Road Cleat For All Types of Riders For anyone unsure about which cleats to choose, the SM-SH11 are a great starting point. With their large float range and centered pivot point, Shimano’s Yellow SPD-SL cleats allow the toes to point in a wide range of angles and provide more room for error during set-up while still delivering an efficient connection between rider and bike. So if you're new to cycling, experience knee pain, lack flexibility, or simply don’t know where to begin, these cleats are your best bet. FEATURES: - SM-SH11 Yellow SPD-SL cleats come stock with most Shimano SPD-SL pedals and are a great choice for the majority of cyclists. They feature a six-degree float range (three degrees in each direction), which allows for free movement and low joint stress while still creating a solid connection between rider and bike. - Customizable: Seamlessly compatible with Shimano SPD-SL pedals, which allow you to adjust the spring force required to clip in and out of your pedals - Ease of Disengagement: Feature a 13-degree clip-out angle, allowing you to quickly get out of your pedals when the time calls - Off-Bike Friendly: Cleat size and shape provide stable walking platform and are less prone to clogging with dirt when off bike - Built to Last: Composite construction combines injection molded main body with grip-enhancing TPU tips that are durable and maintain long lasting pedal engagement